Immersion Heaters

Product Details:

Magma Electric Tubular Heater are the most versatile and the best suited solutions to a large number of applications. Inside the metal tube, a heater coil is embedded and electrically isolated in highly compressed magnesiumoxide. The optimized structure and very high density of the magnesium oxide form the basis for the excellentmechanical and thermal characteristics of the Magma Electric Tubular Heater. They can also be fitted with thermostats and temperature limiters in most applications. Tubular heating elements perform exceptional heat transferby conduction, convection or radiation to heat liquids, air, gases and surfaces. Bends are made to customer requirements.

Tubular elements from Magma are factory-configured to almost any shape or size. Custom bending diameters canbe made upon request. Typically using steel, stainless steel, Incoloy, inconel or titanium alloys, tubular elements are often regarded as the foundation of all heating elements. These heating elements have a strong outer sheath to help protect the heater from physical stress and uses high quality alloys to allow efficient heat transfer from resistance coil to your heating medium.

Careful selection of materials, precise manufacturing techniques as well as numerous tests and inspections ensurethat our Electric Tubular Heater conform to high quality standards and offer an exceptionally long service life.

Tubular heating elements may absorb moisture if they sit idle for a long period of time or get exposed to a humid environment. This might lower the dielectric characteristics of the MgO insulation and cause electrical shorting and premature failure. In order to prove the electrical integrity of a tubular heater, the insulation resistance of each circuit to ground should be checked using a 50 VDC megger. An initial reading of 50,000 ohms or more is acceptable in the field. If heaters do not pass the megohm test they should be dried out. An ideal drying procedure is oven-drying at 375F after removing the terminal hardware. An alternate procedure is to apply a lower voltage (please consult factory for instructions). The target is to attain at least 2 megohms. 

The two most critical factors that affect the durability of a tubular heater are: 

• Sheath material 
• Watt density

The sheath material type of a tubular heater depends on the operating temperature and the corrosivity of the medium within which the heater will operate. The watt density distribution on the surface of a tubular heater is critical for two reasons. First it determines the temperature that a heating element sheath will attain within the conditions that the heater is subjected to. The second reason is that every material has a specific maximum watt density that it can tolerate during its heating cycle. Table 1 below lists various sheath materials, maximum allowable temperatures and mediums within which they are recommended to operate. 

Price Range: 250-15000rs/Unit

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of Finned Tubular Heater.

Durability of finned tubular heater is affected by two critical factors i.e. sheath material and its watt density. As steel is very efficient in heat transfer the standard finned tubular heaters are made of steel sheath and steel fins (750°F max. surface temperature). These heaters have a plain-surface finish. Finned tubular heaters could be made withstainless steel sheath and stainless steel fins for corrosive environments or high temperature applications (above750°F). Safe watt densities that keep surface temperatures below allowable limits depend on the speed of the incoming air and its outlet temperature.

• To heat stagnant air
• For heating circulating air and air flows
• For gas heating
• For heating of air ducts
• As pre-heating unit in machines
• In air-conditioning ducts
• In industrial furnaces and drying chambers
• For shrink packaging machines
• Heating elements in air heaters

Available Power:

• Upto 1500W

Price Range: 250-15000rs/unit.

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of Flanged Immersion Heaters.

One of the most widely used method for heating liquids such as water, oil, heat transfer fluid and corrosive solutions is Magma Flanged immersion heaters. This method is energy efficient and easily monitored and controlled. They are designed for use in tanks and pressurized vessels.

Magma Flanged immersion heaters are easy to install and maintain to provide heat for many processes. These through the-side immersion heaters utilize standard pipe flanges of various ranges in diameter to support high tank pressures of liquids. They are installed through a matching companion flange, obtainable from local industrial supply houses, to the tank wall.

Many different alloys used in the Magma flanged immersion heaters allow the flexibility to help resist corrosion and maintain life longevity of the flanged heater. Steel flanges are typically used for lubricant oils, heavy and light oils, waxes as well as mildly corrosive liquids and low flow gas heating. Applications of steel flanges are process water, soap and detergent solutions as well as de-mineralized or deionized water. Stainless steel flanged heating elements are used with mildly corrosive solutions as well as severe corrosive solutions. Food applications use stainless steel for sanitary purposes.

The sheath materials used can be steel, stainless steel, copper as well as exotic alloys such as Inconel, hast alloy and titanium. Extremely corrosive environments such as salt water should use exotic alloys such as titanium to avoid sheath breach over excessive durations. Industries that use exotic alloys can include military, Chemical and process industries.

Magma offers flanged immersion heaters in varying kilowatts ratings, voltages, temperature ranges, sheath materials and so on. A wide selection of watt densities, heating outputs and flange sizes and ratings make this an excellent heater for all tanks, or irregularly shaped vessels.

Typical applications include preheating different grades of oil, cleaning tanks and heat transfer

Electric Immersion heaters may heat water immediately adjacent to the heating element high enough to promote the formation of scale, commonly calcium carbonate, in hard water areas. This accumulates on the element, and over time, as the element expands and contracts through its heating cycle, the scale cracks off and drops to the bottom of the tank, progressively filling up the tank. This reduces the tank's capacity and, where the immersion heater is secondary to the heating of the water by a coil fed from a gas or oil-fired boiler, can reduce the efficiency of the primary heating source by covering that other coil and in turn reducing its efficiency. Regular flushing-out of accumulated sediment can reduce this problem.Such problems can be avoided at the design stage, by maximising the amount of hot element in the liquid, thus reducing the watts density. This reduces the working temperature of the surface of the element, reducing the build up of limescale. So watt density has to be revised as per application. 

Price Range: 1000-500000rs/unit.

Product Details:

Magma Industrial Immersion Heaters are primarily designed to generate all heat immersed in liquid or gases which are installed in a tank or container. These heaters are virtually 100% energy efficient. These versatile heaters can also be formed and shaped into various geometries for radiant heating and contact surface heating applications. 

Magma has extensive experience with custom-designed immersion heaters for the tank, reservoir, and circulation flow applications. They are constructed of one or more heater elements of various lengths & dimensions, diameters of tubes which are brazed or welded into numerous different types of mounting fittings as per requirements. Hot water and steam are required for numerous industrial and commercial applications. For a good percentage of these, an immersed tubular heating element is the most efficient, inexpensive, and robust solution. 

Standard or custom-engineered designs are available for tailored solutions to application requirements. Installation for various applications can be over-the-side. flanged and threaded or screw plug immersion heaters. 

Price Range: 500-50000Rs/Unit

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of Oil Immersion Heaters.

Length Available Upto: 20Inch

Price Range: 1000-500000rs/unit

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of Flanged Immersion Heaters.

One of the most widely used method for heating liquids such as water, oil, heat transfer fluid and corrosive solutions is Magma Flanged immersion heaters. This method is energy efficient and easily monitored and controlled. They are designed for use in tanks and pressurized vessels.

Magma Flanged immersion heaters are easy to install and maintain to provide heat for many processes. These through the-side immersion heaters utilize standard pipe flanges of various ranges in diameter to support high tank pressures of liquids. They are installed through a matching companion flange, obtainable from local industrial supply houses, to the tank wall.

Many different alloys used in the Magma flanged immersion heaters allow the flexibility to help resist corrosion and maintain life longevity of the flanged heater. Steel flanges are typically used for lubricant oils, heavy and light oils, waxes as well as mildly corrosive liquids and low flow gas heating. Applications of steel flanges are process water, soap and detergent solutions as well as de-mineralized or deionized water. Stainless steel flanged heating elements are used with mildly corrosive solutions as well as severe corrosive solutions. Food applications use stainless steel for sanitary purposes.

The sheath materials used can be steel, stainless steel, copper as well as exotic alloys such as Inconel, hast alloy and titanium. Extremely corrosive environments such as salt water should use exotic alloys such as titanium to avoid sheath breach over excessive durations. Industries that use exotic alloys can include military, Chemical and process industries.

Magma offers flanged immersion heaters in varying kilowatts ratings, voltages, temperature ranges, sheath materials and so on. A wide selection of watt densities, heating outputs and flange sizes and ratings make this an excellent heater for all tanks, or irregularly shaped vessels.

Typical applications include preheating different grades of oil, cleaning tanks and heat transfer

Electric Immersion heaters may heat water immediately adjacent to the heating element high enough to promote the formation of scale, commonly calcium carbonate, in hard water areas. This accumulates on the element, and over time, as the element expands and contracts through its heating cycle, the scale cracks off and drops to the bottom of the tank, progressively filling up the tank. This reduces the tank's capacity and, where the immersion heater is secondary to the heating of the water by a coil fed from a gas or oil-fired boiler, can reduce the efficiency of the primary heating source by covering that other coil and in turn reducing its efficiency. Regular flushing-out of accumulated sediment can reduce this problem.Such problems can be avoided at the design stage, by maximising the amount of hot element in the liquid, thus reducing the watts density. This reduces the working temperature of the surface of the element, reducing the build up of limescale. So watt density has to be revised as per application. 

Price Range: 1000-500000rs/unit.

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of  HEATING SYSTEMS.

One of the most widely used method for heating liquids such as water, oil, heat transfer fluid and corrosive solutions is Magma Flanged immersion heaters. This method is energy efficient and easily monitored and controlled. They are designed for use in tanks and pressurized vessels.

Magma Flanged immersion heaters are easy to install and maintain to provide heat for many processes. These through the-side immersion heaters utilize standard pipe flanges of various ranges in diameter to support high tank pressures of liquids. They are installed through a matching companion flange, obtainable from local industrial supply houses, to the tank wall.

Many different alloys used in the Magma flanged immersion heaters allow the flexibility to help resist corrosion and maintain life longevity of the flanged heater. Steel flanges are typically used for lubricant oils, heavy and light oils, waxes as well as mildly corrosive liquids and low flow gas heating. Applications of steel flanges are process water, soap and detergent solutions as well as de-mineralized or deionized water. Stainless steel flanged heating elements are used with mildly corrosive solutions as well as severe corrosive solutions. Food applications use stainless steel for sanitary purposes.

The sheath materials used can be steel, stainless steel, copper as well as exotic alloys such as Inconel, hast alloy and titanium. Extremely corrosive environments such as salt water should use exotic alloys such as titanium to avoid sheath breach over excessive durations. Industries that use exotic alloys can include military, Chemical and process industries.

Magma offers flanged immersion heaters in varying kilowatts ratings, voltages, temperature ranges, sheath materials and so on. A wide selection of watt densities, heating outputs and flange sizes and ratings make this an excellent heater for all tanks, or irregularly shaped vessels.

Typical applications include preheating different grades of oil, cleaning tanks and heat transfer

Electric Immersion heaters may heat water immediately adjacent to the heating element high enough to promote the formation of scale, commonly calcium carbonate, in hard water areas. This accumulates on the element, and over time, as the element expands and contracts through its heating cycle, the scale cracks off and drops to the bottom of the tank, progressively filling up the tank. This reduces the tank's capacity and, where the immersion heater is secondary to the heating of the water by a coil fed from a gas or oil-fired boiler, can reduce the efficiency of the primary heating source by covering that other coil and in turn reducing its efficiency. Regular flushing-out of accumulated sediment can reduce this problem.Such problems can be avoided at the design stage, by maximising the amount of hot element in the liquid, thus reducing the watts density. This reduces the working temperature of the surface of the element, reducing the build up of limescale. So watt density has to be revised as per application. 

Price Range: 1000-500000rs/unit.

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of  HEATING SYSTEMS.

One of the most widely used method for heating liquids such as water, oil, heat transfer fluid and corrosive solutions is Magma Flanged immersion heaters. This method is energy efficient and easily monitored and controlled. They are designed for use in tanks and pressurized vessels.

Magma Flanged immersion heaters are easy to install and maintain to provide heat for many processes. These through the-side immersion heaters utilize standard pipe flanges of various ranges in diameter to support high tank pressures of liquids. They are installed through a matching companion flange, obtainable from local industrial supply houses, to the tank wall.

Many different alloys used in the Magma flanged immersion heaters allow the flexibility to help resist corrosion and maintain life longevity of the flanged heater. Steel flanges are typically used for lubricant oils, heavy and light oils, waxes as well as mildly corrosive liquids and low flow gas heating. Applications of steel flanges are process water, soap and detergent solutions as well as de-mineralized or deionized water. Stainless steel flanged heating elements are used with mildly corrosive solutions as well as severe corrosive solutions. Food applications use stainless steel for sanitary purposes.

The sheath materials used can be steel, stainless steel, copper as well as exotic alloys such as Inconel, hast alloy and titanium. Extremely corrosive environments such as salt water should use exotic alloys such as titanium to avoid sheath breach over excessive durations. Industries that use exotic alloys can include military, Chemical and process industries.

Magma offers flanged immersion heaters in varying kilowatts ratings, voltages, temperature ranges, sheath materials and so on. A wide selection of watt densities, heating outputs and flange sizes and ratings make this an excellent heater for all tanks, or irregularly shaped vessels.

Typical applications include preheating different grades of oil, cleaning tanks and heat transfer

Electric Immersion heaters may heat water immediately adjacent to the heating element high enough to promote the formation of scale, commonly calcium carbonate, in hard water areas. This accumulates on the element, and over time, as the element expands and contracts through its heating cycle, the scale cracks off and drops to the bottom of the tank, progressively filling up the tank. This reduces the tank's capacity and, where the immersion heater is secondary to the heating of the water by a coil fed from a gas or oil-fired boiler, can reduce the efficiency of the primary heating source by covering that other coil and in turn reducing its efficiency. Regular flushing-out of accumulated sediment can reduce this problem.Such problems can be avoided at the design stage, by maximising the amount of hot element in the liquid, thus reducing the watts density. This reduces the working temperature of the surface of the element, reducing the build up of limescale. So watt density has to be revised as per application. 

Price Range: 1000-500000rs/unit.

Product Details:

Magma Industrial Immersion Heaters are primarily designed to generate all heat immersed in liquid or gases which are installed in a tank or container. These heaters are virtually 100% energy efficient. These versatile heaters can also be formed and shaped into various geometries for radiant heating and contact surface heating applications. 

Magma has extensive experience with custom-designed immersion heaters for the tank, reservoir, and circulation flow applications. They are constructed of one or more heater elements of various lengths & dimensions, diameters of tubes which are brazed or welded into numerous different types of mounting fittings as per requirements. Hot water and steam are required for numerous industrial and commercial applications. For a good percentage of these, an immersed tubular heating element is the most efficient, inexpensive, and robust solution. 

Standard or custom-engineered designs are available for tailored solutions to application requirements. Installation for various applications can be over-the-side. flanged and threaded or screw plug immersion heaters. 

Price Range: 500-50000Rs/Unit

Product Details:

Magma Industrial Immersion Heaters are primarily designed to generate all heat immersed in liquid or gases which are installed in a tank or container. These heaters are virtually 100% energy efficient. These versatile heaters can also be formed and shaped into various geometries for radiant heating and contact surface heating applications. 

Magma has extensive experience with custom-designed immersion heaters for the tank, reservoir, and circulation flow applications. They are constructed of one or more heater elements of various lengths & dimensions, diameters of tubes which are brazed or welded into numerous different types of mounting fittings as per requirements. Hot water and steam are required for numerous industrial and commercial applications. For a good percentage of these, an immersed tubular heating element is the most efficient, inexpensive, and robust solution. 

Standard or custom-engineered designs are available for tailored solutions to application requirements. Installation for various applications can be over-the-side. flanged and threaded or screw plug immersion heaters. 

Price Range: 500-50000Rs/Unit

Product Details:

Magma Industrial Immersion Heaters are primarily designed to generate all heat immersed in liquid or gases which are installed in a tank or container. These heaters are virtually 100% energy efficient. These versatile heaters can also be formed and shaped into various geometries for radiant heating and contact surface heating applications. 

Magma has extensive experience with custom-designed immersion heaters for the tank, reservoir, and circulation flow applications. They are constructed of one or more heater elements of various lengths & dimensions, diameters of tubes which are brazed or welded into numerous different types of mounting fittings as per requirements. Hot water and steam are required for numerous industrial and commercial applications. For a good percentage of these, an immersed tubular heating element is the most efficient, inexpensive, and robust solution. 

Standard or custom-engineered designs are available for tailored solutions to application requirements. Installation for various applications can be over-the-side. flanged and threaded or screw plug immersion heaters. 

Price Range: 500-50000Rs/Unit

Product Details:

Magma Industrial Immersion Heaters are primarily designed to generate all heat immersed in liquid or gases which are installed in a tank or container. These heaters are virtually 100% energy efficient. These versatile heaters can also be formed and shaped into various geometries for radiant heating and contact surface heating applications. 

Magma has extensive experience with custom-designed immersion heaters for the tank, reservoir, and circulation flow applications. They are constructed of one or more heater elements of various lengths & dimensions, diameters of tubes which are brazed or welded into numerous different types of mounting fittings as per requirements. Hot water and steam are required for numerous industrial and commercial applications. For a good percentage of these, an immersed tubular heating element is the most efficient, inexpensive, and robust solution. 

Standard or custom-engineered designs are available for tailored solutions to application requirements. Installation for various applications can be over-the-side. flanged and threaded or screw plug immersion heaters. 

Price Range: 500-50000Rs/Unit

Additional Information:

• Item Code: 8516
• Production Capacity: Customised

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of Flanged / BSP Immersion Heaters.

One of the most widely used method for heating liquids such as water, oil, heat transfer fluid and corrosive solutions is Magma Flanged immersion heaters. This method is energy efficient and easily monitored and controlled. They are designed for use in tanks and pressurized vessels.

Magma Flanged immersion heaters are easy to install and maintain to provide heat for many processes. These through the-side immersion heaters utilize standard pipe flanges of various ranges in diameter to support high tank pressures of liquids. They are installed through a matching companion flange, obtainable from local industrial supply houses, to the tank wall.

Many different alloys used in the Magma flanged immersion heaters allow the flexibility to help resist corrosion and maintain life longevity of the flanged heater. Steel flanges are typically used for lubricant oils, heavy and light oils, waxes as well as mildly corrosive liquids and low flow gas heating. Applications of steel flanges are process water, soap and detergent solutions as well as de-mineralized or deionized water. Stainless steel flanged heating elements are used with mildly corrosive solutions as well as severe corrosive solutions. Food applications use stainless steel for sanitary purposes.

The sheath materials used can be steel, stainless steel, copper as well as exotic alloys such as Inconel, hast alloy and titanium. Extremely corrosive environments such as salt water should use exotic alloys such as titanium to avoid sheath breach over excessive durations. Industries that use exotic alloys can include military, Chemical and process industries.

Magma offers flanged immersion heaters in varying kilowatts ratings, voltages, temperature ranges, sheath materials and so on. A wide selection of watt densities, heating outputs and flange sizes and ratings make this an excellent heater for all tanks, or irregularly shaped vessels.

Typical applications include preheating different grades of oil, cleaning tanks and heat transfer

Electric Immersion heaters may heat water immediately adjacent to the heating element high enough to promote the formation of scale, commonly calcium carbonate, in hard water areas. This accumulates on the element, and over time, as the element expands and contracts through its heating cycle, the scale cracks off and drops to the bottom of the tank, progressively filling up the tank. This reduces the tank's capacity and, where the immersion heater is secondary to the heating of the water by a coil fed from a gas or oil-fired boiler, can reduce the efficiency of the primary heating source by covering that other coil and in turn reducing its efficiency. Regular flushing-out of accumulated sediment can reduce this problem.Such problems can be avoided at the design stage, by maximising the amount of hot element in the liquid, thus reducing the watts density. This reduces the working temperature of the surface of the element, reducing the build up of limescale. So watt density has to be revised as per application. 

Price Range: 1000-500000rs/unit.

Product Details:

Magma Industrial Immersion Heaters are primarily designed to generate all heat immersed in liquid or gases which are installed in a tank or container. These heaters are virtually 100% energy efficient. These versatile heaters can also be formed and shaped into various geometries for radiant heating and contact surface heating applications. 

Magma has extensive experience with custom-designed immersion heaters for the tank, reservoir, and circulation flow applications. They are constructed of one or more heater elements of various lengths & dimensions, diameters of tubes which are brazed or welded into numerous different types of mounting fittings as per requirements. Hot water and steam are required for numerous industrial and commercial applications. For a good percentage of these, an immersed tubular heating element is the most efficient, inexpensive, and robust solution. 

Standard or custom-engineered designs are available for tailored solutions to application requirements. Installation for various applications can be over-the-side. flanged and threaded or screw plug immersion heaters. 

Price Range: 500-50000Rs/Unit

Product Details:

Magma Industrial Immersion Heaters are primarily designed to generate all heat immersed in liquid or gases which are installed in a tank or container. These heaters are virtually 100% energy efficient. These versatile heaters can also be formed and shaped into various geometries for radiant heating and contact surface heating applications. 

Magma has extensive experience with custom-designed immersion heaters for the tank, reservoir, and circulation flow applications. They are constructed of one or more heater elements of various lengths & dimensions, diameters of tubes which are brazed or welded into numerous different types of mounting fittings as per requirements. Hot water and steam are required for numerous industrial and commercial applications. For a good percentage of these, an immersed tubular heating element is the most efficient, inexpensive, and robust solution. 

Standard or custom-engineered designs are available for tailored solutions to application requirements. Installation for various applications can be over-the-side. flanged and threaded or screw plug immersion heaters. 

Price Range: 500-50000Rs/Unit

Product Details:

Magma Industrial Immersion Heaters are primarily designed to generate all heat immersed in liquid or gases which are installed in a tank or container. These heaters are virtually 100% energy efficient. These versatile heaters can also be formed and shaped into various geometries for radiant heating and contact surface heating applications. 

Magma has extensive experience with custom-designed immersion heaters for the tank, reservoir, and circulation flow applications. They are constructed of one or more heater elements of various lengths & dimensions, diameters of tubes which are brazed or welded into numerous different types of mounting fittings as per requirements. Hot water and steam are required for numerous industrial and commercial applications. For a good percentage of these, an immersed tubular heating element is the most efficient, inexpensive, and robust solution. 

Standard or custom-engineered designs are available for tailored solutions to application requirements. Installation for various applications can be over-the-side. flanged and threaded or screw plug immersion heaters. 

Price Range: 500-50000Rs/Unit

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of Tubular Heaters.

Available Power:

• Upto 1000 W

Price Range: 250-15000rs/unit.

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of Flanged Immersion Heaters.

One of the most widely used method for heating liquids such as water, oil, heat transfer fluid and corrosive solutions is Magma Flanged immersion heaters. This method is energy efficient and easily monitored and controlled. They are designed for use in tanks and pressurized vessels.

Magma Flanged immersion heaters are easy to install and maintain to provide heat for many processes. These through the-side immersion heaters utilize standard pipe flanges of various ranges in diameter to support high tank pressures of liquids. They are installed through a matching companion flange, obtainable from local industrial supply houses, to the tank wall.

Many different alloys used in the Magma flanged immersion heaters allow the flexibility to help resist corrosion and maintain life longevity of the flanged heater. Steel flanges are typically used for lubricant oils, heavy and light oils, waxes as well as mildly corrosive liquids and low flow gas heating. Applications of steel flanges are process water, soap and detergent solutions as well as de-mineralized or deionized water. Stainless steel flanged heating elements are used with mildly corrosive solutions as well as severe corrosive solutions. Food applications use stainless steel for sanitary purposes.

The sheath materials used can be steel, stainless steel, copper as well as exotic alloys such as Inconel, hast alloy and titanium. Extremely corrosive environments such as salt water should use exotic alloys such as titanium to avoid sheath breach over excessive durations. Industries that use exotic alloys can include military, Chemical and process industries.

Magma offers flanged immersion heaters in varying kilowatts ratings, voltages, temperature ranges, sheath materials and so on. A wide selection of watt densities, heating outputs and flange sizes and ratings make this an excellent heater for all tanks, or irregularly shaped vessels.

Typical applications include preheating different grades of oil, cleaning tanks and heat transfer

Electric Immersion heaters may heat water immediately adjacent to the heating element high enough to promote the formation of scale, commonly calcium carbonate, in hard water areas. This accumulates on the element, and over time, as the element expands and contracts through its heating cycle, the scale cracks off and drops to the bottom of the tank, progressively filling up the tank. This reduces the tank's capacity and, where the immersion heater is secondary to the heating of the water by a coil fed from a gas or oil-fired boiler, can reduce the efficiency of the primary heating source by covering that other coil and in turn reducing its efficiency. Regular flushing-out of accumulated sediment can reduce this problem.Such problems can be avoided at the design stage, by maximising the amount of hot element in the liquid, thus reducing the watts density. This reduces the working temperature of the surface of the element, reducing the build up of limescale. So watt density has to be revised as per application. 

Price Range: 1000-500000rs/unit.

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of Flanged / BSP Immersion Heaters.

One of the most widely used method for heating liquids such as water, oil, heat transfer fluid and corrosive solutions is Magma Flanged immersion heaters. This method is energy efficient and easily monitored and controlled. They are designed for use in tanks and pressurized vessels.

Magma Flanged immersion heaters are easy to install and maintain to provide heat for many processes. These through the-side immersion heaters utilize standard pipe flanges of various ranges in diameter to support high tank pressures of liquids. They are installed through a matching companion flange, obtainable from local industrial supply houses, to the tank wall.

Many different alloys used in the Magma flanged immersion heaters allow the flexibility to help resist corrosion and maintain life longevity of the flanged heater. Steel flanges are typically used for lubricant oils, heavy and light oils, waxes as well as mildly corrosive liquids and low flow gas heating. Applications of steel flanges are process water, soap and detergent solutions as well as de-mineralized or deionized water. Stainless steel flanged heating elements are used with mildly corrosive solutions as well as severe corrosive solutions. Food applications use stainless steel for sanitary purposes.

The sheath materials used can be steel, stainless steel, copper as well as exotic alloys such as Inconel, hast alloy and titanium. Extremely corrosive environments such as salt water should use exotic alloys such as titanium to avoid sheath breach over excessive durations. Industries that use exotic alloys can include military, Chemical and process industries.

Magma offers flanged immersion heaters in varying kilowatts ratings, voltages, temperature ranges, sheath materials and so on. A wide selection of watt densities, heating outputs and flange sizes and ratings make this an excellent heater for all tanks, or irregularly shaped vessels.

Typical applications include preheating different grades of oil, cleaning tanks and heat transfer

Electric Immersion heaters may heat water immediately adjacent to the heating element high enough to promote the formation of scale, commonly calcium carbonate, in hard water areas. This accumulates on the element, and over time, as the element expands and contracts through its heating cycle, the scale cracks off and drops to the bottom of the tank, progressively filling up the tank. This reduces the tank's capacity and, where the immersion heater is secondary to the heating of the water by a coil fed from a gas or oil-fired boiler, can reduce the efficiency of the primary heating source by covering that other coil and in turn reducing its efficiency. Regular flushing-out of accumulated sediment can reduce this problem.Such problems can be avoided at the design stage, by maximising the amount of hot element in the liquid, thus reducing the watts density. This reduces the working temperature of the surface of the element, reducing the build up of limescale. So watt density has to be revised as per application. 

Price Range: 1000-500000rs/unit.

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of Flanged / BSP Immersion Heaters.

One of the most widely used method for heating liquids such as water, oil, heat transfer fluid and corrosive solutions is Magma Flanged immersion heaters. This method is energy efficient and easily monitored and controlled. They are designed for use in tanks and pressurized vessels.

Magma Flanged immersion heaters are easy to install and maintain to provide heat for many processes. These through the-side immersion heaters utilize standard pipe flanges of various ranges in diameter to support high tank pressures of liquids. They are installed through a matching companion flange, obtainable from local industrial supply houses, to the tank wall.

Many different alloys used in the Magma flanged immersion heaters allow the flexibility to help resist corrosion and maintain life longevity of the flanged heater. Steel flanges are typically used for lubricant oils, heavy and light oils, waxes as well as mildly corrosive liquids and low flow gas heating. Applications of steel flanges are process water, soap and detergent solutions as well as de-mineralized or deionized water. Stainless steel flanged heating elements are used with mildly corrosive solutions as well as severe corrosive solutions. Food applications use stainless steel for sanitary purposes.

The sheath materials used can be steel, stainless steel, copper as well as exotic alloys such as Inconel, hast alloy and titanium. Extremely corrosive environments such as salt water should use exotic alloys such as titanium to avoid sheath breach over excessive durations. Industries that use exotic alloys can include military, Chemical and process industries.

Magma offers flanged immersion heaters in varying kilowatts ratings, voltages, temperature ranges, sheath materials and so on. A wide selection of watt densities, heating outputs and flange sizes and ratings make this an excellent heater for all tanks, or irregularly shaped vessels.

Typical applications include preheating different grades of oil, cleaning tanks and heat transfer

Electric Immersion heaters may heat water immediately adjacent to the heating element high enough to promote the formation of scale, commonly calcium carbonate, in hard water areas. This accumulates on the element, and over time, as the element expands and contracts through its heating cycle, the scale cracks off and drops to the bottom of the tank, progressively filling up the tank. This reduces the tank's capacity and, where the immersion heater is secondary to the heating of the water by a coil fed from a gas or oil-fired boiler, can reduce the efficiency of the primary heating source by covering that other coil and in turn reducing its efficiency. Regular flushing-out of accumulated sediment can reduce this problem.Such problems can be avoided at the design stage, by maximising the amount of hot element in the liquid, thus reducing the watts density. This reduces the working temperature of the surface of the element, reducing the build up of limescale. So watt density has to be revised as per application. 

Price Range: 1000-500000rs/unit.

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of  HEATING SYSTEMS.

One of the most widely used method for heating liquids such as water, oil, heat transfer fluid and corrosive solutions is Magma Flanged immersion heaters. This method is energy efficient and easily monitored and controlled. They are designed for use in tanks and pressurized vessels.

Magma Flanged immersion heaters are easy to install and maintain to provide heat for many processes. These through the-side immersion heaters utilize standard pipe flanges of various ranges in diameter to support high tank pressures of liquids. They are installed through a matching companion flange, obtainable from local industrial supply houses, to the tank wall.

Many different alloys used in the Magma flanged immersion heaters allow the flexibility to help resist corrosion and maintain life longevity of the flanged heater. Steel flanges are typically used for lubricant oils, heavy and light oils, waxes as well as mildly corrosive liquids and low flow gas heating. Applications of steel flanges are process water, soap and detergent solutions as well as de-mineralized or deionized water. Stainless steel flanged heating elements are used with mildly corrosive solutions as well as severe corrosive solutions. Food applications use stainless steel for sanitary purposes.

The sheath materials used can be steel, stainless steel, copper as well as exotic alloys such as Inconel, hast alloy and titanium. Extremely corrosive environments such as salt water should use exotic alloys such as titanium to avoid sheath breach over excessive durations. Industries that use exotic alloys can include military, Chemical and process industries.

Magma offers flanged immersion heaters in varying kilowatts ratings, voltages, temperature ranges, sheath materials and so on. A wide selection of watt densities, heating outputs and flange sizes and ratings make this an excellent heater for all tanks, or irregularly shaped vessels.

Typical applications include preheating different grades of oil, cleaning tanks and heat transfer

Electric Immersion heaters may heat water immediately adjacent to the heating element high enough to promote the formation of scale, commonly calcium carbonate, in hard water areas. This accumulates on the element, and over time, as the element expands and contracts through its heating cycle, the scale cracks off and drops to the bottom of the tank, progressively filling up the tank. This reduces the tank's capacity and, where the immersion heater is secondary to the heating of the water by a coil fed from a gas or oil-fired boiler, can reduce the efficiency of the primary heating source by covering that other coil and in turn reducing its efficiency. Regular flushing-out of accumulated sediment can reduce this problem.Such problems can be avoided at the design stage, by maximising the amount of hot element in the liquid, thus reducing the watts density. This reduces the working temperature of the surface of the element, reducing the build up of limescale. So watt density has to be revised as per application. 

Price Range: 1000-500000rs/unit.

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of Flanged /BSP  Immersion Heaters.

One of the most widely used method for heating liquids such as water, oil, heat transfer fluid and corrosive solutions is Magma Flanged immersion heaters. This method is energy efficient and easily monitored and controlled. They are designed for use in tanks and pressurized vessels.

Magma Flanged immersion heaters are easy to install and maintain to provide heat for many processes. These through the-side immersion heaters utilize standard pipe flanges of various ranges in diameter to support high tank pressures of liquids. They are installed through a matching companion flange, obtainable from local industrial supply houses, to the tank wall.

Many different alloys used in the Magma flanged immersion heaters allow the flexibility to help resist corrosion and maintain life longevity of the flanged heater. Steel flanges are typically used for lubricant oils, heavy and light oils, waxes as well as mildly corrosive liquids and low flow gas heating. Applications of steel flanges are process water, soap and detergent solutions as well as de-mineralized or deionized water. Stainless steel flanged heating elements are used with mildly corrosive solutions as well as severe corrosive solutions. Food applications use stainless steel for sanitary purposes.

The sheath materials used can be steel, stainless steel, copper as well as exotic alloys such as Inconel, hast alloy and titanium. Extremely corrosive environments such as salt water should use exotic alloys such as titanium to avoid sheath breach over excessive durations. Industries that use exotic alloys can include military, Chemical and process industries.

Magma offers flanged immersion heaters in varying kilowatts ratings, voltages, temperature ranges, sheath materials and so on. A wide selection of watt densities, heating outputs and flange sizes and ratings make this an excellent heater for all tanks, or irregularly shaped vessels.

Typical applications include preheating different grades of oil, cleaning tanks and heat transfer

Electric Immersion heaters may heat water immediately adjacent to the heating element high enough to promote the formation of scale, commonly calcium carbonate, in hard water areas. This accumulates on the element, and over time, as the element expands and contracts through its heating cycle, the scale cracks off and drops to the bottom of the tank, progressively filling up the tank. This reduces the tank's capacity and, where the immersion heater is secondary to the heating of the water by a coil fed from a gas or oil-fired boiler, can reduce the efficiency of the primary heating source by covering that other coil and in turn reducing its efficiency. Regular flushing-out of accumulated sediment can reduce this problem.Such problems can be avoided at the design stage, by maximising the amount of hot element in the liquid, thus reducing the watts density. This reduces the working temperature of the surface of the element, reducing the build up of limescale. So watt density has to be revised as per application. 

Price Range: 1000-500000rs/unit.

Product Details:

Magma Industrial Immersion Heaters are primarily designed to generate all heat immersed in liquid or gases which are installed in a tank or container. These heaters are virtually 100% energy efficient. These versatile heaters can also be formed and shaped into various geometries for radiant heating and contact surface heating applications. 

Magma has extensive experience with custom-designed immersion heaters for the tank, reservoir, and circulation flow applications. They are constructed of one or more heater elements of various lengths & dimensions, diameters of tubes which are brazed or welded into numerous different types of mounting fittings as per requirements. Hot water and steam are required for numerous industrial and commercial applications. For a good percentage of these, an immersed tubular heating element is the most efficient, inexpensive, and robust solution. 

Standard or custom-engineered designs are available for tailored solutions to application requirements. Installation for various applications can be over-the-side. flanged and threaded or screw plug immersion heaters. 

Price Range: 500-50000Rs/Unit

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of Immersion Water Heater.

Price Range: 2000-500000rs/unit

Product Details:

With enriched industrial experience and knowledge, we are providing an excellent range of Flanged / BSP Immersion Heaters.

One of the most widely used method for heating liquids such as water, oil, heat transfer fluid and corrosive solutions is Magma Flanged immersion heaters. This method is energy efficient and easily monitored and controlled. They are designed for use in tanks and pressurized vessels.

Magma Flanged immersion heaters are easy to install and maintain to provide heat for many processes. These through the-side immersion heaters utilize standard pipe flanges of various ranges in diameter to support high tank pressures of liquids. They are installed through a matching companion flange, obtainable from local industrial supply houses, to the tank wall.

Many different alloys used in the Magma flanged immersion heaters allow the flexibility to help resist corrosion and maintain life longevity of the flanged heater. Steel flanges are typically used for lubricant oils, heavy and light oils, waxes as well as mildly corrosive liquids and low flow gas heating. Applications of steel flanges are process water, soap and detergent solutions as well as de-mineralized or deionized water. Stainless steel flanged heating elements are used with mildly corrosive solutions as well as severe corrosive solutions. Food applications use stainless steel for sanitary purposes.

The sheath materials used can be steel, stainless steel, copper as well as exotic alloys such as Inconel, hast alloy and titanium. Extremely corrosive environments such as salt water should use exotic alloys such as titanium to avoid sheath breach over excessive durations. Industries that use exotic alloys can include military, Chemical and process industries.

Magma offers flanged immersion heaters in varying kilowatts ratings, voltages, temperature ranges, sheath materials and so on. A wide selection of watt densities, heating outputs and flange sizes and ratings make this an excellent heater for all tanks, or irregularly shaped vessels.

Typical applications include preheating different grades of oil, cleaning tanks and heat transfer

Electric Immersion heaters may heat water immediately adjacent to the heating element high enough to promote the formation of scale, commonly calcium carbonate, in hard water areas. This accumulates on the element, and over time, as the element expands and contracts through its heating cycle, the scale cracks off and drops to the bottom of the tank, progressively filling up the tank. This reduces the tank's capacity and, where the immersion heater is secondary to the heating of the water by a coil fed from a gas or oil-fired boiler, can reduce the efficiency of the primary heating source by covering that other coil and in turn reducing its efficiency. Regular flushing-out of accumulated sediment can reduce this problem.Such problems can be avoided at the design stage, by maximising the amount of hot element in the liquid, thus reducing the watts density. This reduces the working temperature of the surface of the element, reducing the build up of limescale. So watt density has to be revised as per application. 

Price Range: 1000-500000rs/unit.